Fix Your Belt In 5 Minutes

Assume I would like to take it to someone who's experienced in doing it as the belt wasn't precisely cheap and don't want to destroy it. Practice on the very end (that you'll minimize off later) to get a really feel for the way the drill and Leather interact. Seems just like the Tandy Leather web site store has gone kaput, the belt clean and belt hold hyperlinks don't work any longer. Tom, Unfortunately it seems like this published around the identical time Tandy did a worth increase on the belt blank. Tom: $7 balm + $1 maintain + $2 buckle + $19 belt clean = $29 - $10 from code = $19. I have already got Sno Seal at house and want to keep away from purchasing the Leather Balm if it does the same factor.
If your high precedence is a snug fit, as a substitute put on the belt and pull it to a comfortable position, then mark the belt where the strap tongue touches it. Use heavy objects to crush each end of the belt, with the location where the opening will be punched on top of a block of wooden or different laborious, flat floor. You can even decide to snipping the other end, once it has penetrated the outer layer a bit, as an alternative of drilling an ideal Hole.



I warmth the nail over the range, drive it with pliers, bend the belt on the outlet and smoothen edges with sand paper. Sadly, for those who put a lot pressure on it, the uneven Hole will allow the Leather to tear quite simply. Lay the belt down on a flat floor, incorrect facet up. Measure how far apart the pre-reduce belt holes are in order to place the new belt holes correctly. For the sake of aesthetics, it is best to put in holes as much as the point of the desired closure level.
I got here across this Reddit information awhile ago and was inspired to make my own natural colour Leather belt. I've at all times beloved Tanner Goods pure belt with black buckle however would never be able to justify spending $88 on a belt. That's to not say Tanner would not make amazing stuff, I am just not the kind of man that spends a cheap meal shy of 100 bucks on one belt. All the objects you'll want should be out there regionally at a Leather goods store or pastime retailer.

A nail will make a smoother Hole through a skinny belt, but when you're looking to save time, a screw can be turned by way of the Leather, utilizing its threads to tear by quicker. I had to make use of scissors to wash every Hole up and it took a LOT of strain simply to get that! I may very well be okay if all you wish to do is make a brand new Hole in a belt but............you get what you pay for. Even fresh out of the box, this set of pliers has a number of play in its alignment - very easy to not get on the anvil sq. and punch an ovular Hole. I wished a belt that was just a little longer, and so I went with a 45″ in. size and a 1″ in. width.
Irrespective of which of the methods beneath you opt for, 90% of your success might be decided not by how the outlet will get there, but by the place you place it in the first place. Or, if you happen to're crazy obsessive (I am), you may make just a little template with some painters tape. There's not much to it: Mark your spot, and place your belt on some scrap wood. Choice #three: The Leather Hole Punch This designated tool is by far essentially the most supreme option.
One doesn't simply whip up a top quality Leather belt that can help instrument bag's or holsters by following this technique. So no you failed and took good Leather and wasted it. An ideal belt is 1/4 inch thick from two prime grain straps bonded and sewn, beveled and burnished coloured with dye and then sealed. I purchased 5 belt blanks, 5 belt retains, completely different dyes and balms, burnisher, and Leather edging software all from Amazon and Tandy. To make this venture even more genuine I went to the Tanner Goods web site and purchased their normal buckles at a cost $eight.00 each in silver, brass, copper and black.

Perhaps you lost or gained some weight; perhaps you discovered the perfect belt at a thrift retailer, nevertheless it's a not the appropriate size; possibly you want a Hole between two of the already present holes-regardless of the subject is, this tutorial will show belt puncher you methods to add nice spherical belt holes. Use a bit of scrap Leather beneath the belt, so that you're not hammering the punch proper into the anvil. The new holes look slightly extra ragged around the edges, but using the belt will assist to smooth them down.
Regardless of which of the methods below you go for, ninety% of your success will probably be decided not by how the opening will get there, but by the place you put it in the first place. Or, in case you're crazy obsessive (I'm), you may make a bit of template with some painters tape. There's not a lot to it: Mark your spot, and place your belt on some scrap wood. Choice #3: The Leather Hole Punch This designated tool is by far probably the most very best possibility.

Leave a Reply

Your email address will not be published. Required fields are marked *